New release from Addiction RC is a body diffuser. This diffuser attaches to the shell and not the chassis like the R31 diffuser. Look for it in stores now. 

Congratulations to Toxic Drift for achieving sponsorship with Team Tetsujin. Im sure this will be the start of something big for Toxic Drift and the east coast RC drift movement.
Team Tetsujin are makers of drift kerbs, and a few car products. They are also track consultants. You can find them on Facebook.
Again hats off to Toxic Drift. 
You done good.....

Waru #006

Tech Racing has released a drift spec silver carbon graphite conversion kit for Tamiyas Ta06. This conversion kit comes with:
2mm silver carbon high traction main chassis
2mm silver carbon high traction upper deck
3mm silver carbon heavy duty dampers stays.
Look for it at RaceDriftJapan.

Wrap-Up Next has released a clear protective sheet to cover the bottom chassis plate of most 1:10 scale RC cars and trucks. They are made of a special tear resistant polyurethane film and are very durable. It has superior strength, flexibility, resilency and transparent. The protective sheets will be available in 125mm x 175mm. and 125mm x 350mm You can use this as a body/shell protectant too. 
Wrap-Up Next has also released a heat sink wrap for brushless motors. This film comes in black and measures 40mm x 113mm.
Simply peel and wrap.  

Its been a while since Drift Stage has given us a video. Here are their latest. "RAZI-Land No.1" and "RAZI-Land No.2"

Here are just a few pictures of the drift demo Toxic Drift put on at G-WiZs Car Show on May 20th in Westfield NJ. 
There are a few more on my Photobucket.

Big thanks to Toxic Drift for the invite.  

Team Tetsujin has recently released their own version of 3mm pulley belts. These belts are made for the front and rear of most RC chassis and range in different sizes.

Front belts sizes range between 180mm to 258mm(180, 201, 204, 207, 210, 213, 219, 222, 225, 228, 234, 237, 240, 243, 246, 249, 252, 255, 258)

Rear belts sizes range between 390mm to 534mm(390, 399, 402, 405, 408, 417, 420, 423, 426, 432, 438, 444, 447, 453, 459, 468, 471, 480, 486, 489, 492, 498, 501, 507, 513, 516, 519, 522, 525, 534)
The large selection of sizes are a big help for countersteer setups.
You can order these through Team Tetsujin on their Facebook page.

Video #53

Overdose RC will be releasing 8* degree Caster hubs and steering knuckles setups for Enroute JXR, Tamiya VDF, VDS, TA06 and the Yokomo DRB.
They will be avilable in black for the JXR and Tamiya, dark blue for Yokomo DRB, and silver and light blue for Tamiya.
Caster and kingpin are set at 8* degrees. They will be in limited supply. So order fast. 
Here is what Overdose has to say: 
"This is not only caster angle, it is also with the advent of a king pin angle. By putting the king pin angle, position the virtual kingpin axis and tire ground approaches. You can offset can be wide optimizing the steering geometry of the drift of mainstream machine Thereby, linear steering characteristics with a sense of grounding. It is also useful for "Pojikyan" of the recent epidemic. Makes it easier to to specification "Pojikyan" than ever before because of the changing in the direction (positive) happens off camber and steering angle by attaching the king pin. In addition, the built-in ball bearing support portion kingpin. Steering allows a more delicate because it can minimize the looseness of kingpin portion.Has become a feature-packed set of two kinds can be selected Ackerman."